Hieff^TM Fast Cell Direct RT-qPCR Kit

Hieff^™ Fast Cell Direct  RT-qPCR Kit based on SYBR Green dye is suitable for RNA extraction from all kinds of animal cells (such as cell lineage wall cells and suspension cells, primary culture cells, various stem cells, iPS cells, etc.), without the need to extract RNA, and can be used directly for qPCR expression analysis, which is short, easy to operate, and has a low error rate. It takes only 1.5 hours to complete the steps from template preparation to reverse transcription reaction and gene expression analysis.

Reverse transcription and fluorescence detection reagents are included in the kit, which can be used for gene expression analysis without the need to purchase additional reagents.

Specifications

Components

Storage

FCD Lysis Buffer and FCD Washing Buffer were melted and stored at 4°C to prevent contamination. FCD Stop Solution?DNase I?4× Hifair™ FCD RT Mix?2× Hieff™ FCD qPCR SYBR Master Mix should be stored at -25~-15?.

Instructions

1. Preparation of cleavage products

1)1. Melt the reagent at room temperature, turn it upside down and mix it gently before use, and use it after slight centrifugation to avoid foaming*.

*Failure to mix the reagents, use of an oscillator for mixing, and failure to configure the reagents on ice can lead to a decrease in the performance of the reaction.

2)Depending on the cell type**, transfer the cells to a centrifuge tube and centrifuge at 5000 rpm for 2 min to collect the cells and aspirate the medium well. If the cells are cultured in 96-well plates, the medium can be aspirated directly.

???????3)Add 150 ?L of FCD Washing Buffer to each well, wash the cells by blowing, centrifuge at 5000 rpm for 2 min, and aspirate the FCD Washing Buffer***.

???????4)Add 48 ?L of FCD Lysis Buffer Solution and 2 ?L of DNase ? Solution to each well, blow and mix at room temperature, then let it stand for 5 minutes, and then add 2.5 ?L of FCD Stop Solution after incubation****, and then blow and mix for about 5 times to obtain the cleavage product*****.

** The basic requirement for the number of cells is 1 × 10⁴ cells per well, and this kit can be used in the range of 1 × 10³ - 1 × 10⁶ cells. if the number of cells is larger, the amount of FCD Lysis Buffer solution and DNase?solution can be increased proportionally as appropriate.

*** Centrifugation conditions vary from cell to cell, so please centrifuge at a speed appropriate for the cells being used.

**** Add 2.5 ?L of FCD Stop Solution to 50 ?L of lysate, and increase the amount of FCD Stop Solution as needed.

***** For long-term storage of cell lysis product solutions, place at -20°C.

5?Melt 4 x Hifair™ FCD RT Mix at room temperature and mix with slight inversion, place on ice and configure the reaction system according to the table below:

*******Recommended use level is 2-5 ?L, try not to exceed 45%.

1. Reverse transcription

Pipette and gently mix the above prepared reaction solution and perform the reverse transcription reaction according to the procedure in the table below:

* The recommended reverse transcription temperature is 55°C. For high GC content templates or complex templates, the reverse transcription temperature can be increased to 60°C. The reverse transcription product can be directly used for downstream RT-qPCR detection. In order to avoid the inhibition of qPCR reaction by the reverse transcription system and to get the appropriate Ct value (10-35), the product can be diluted 10-1000 times and then used. If downstream experiments are not performed for a short time, it can be placed at -20? for storage.

1. Fluorescence quantitative PCR

1?Reaction system configuration

The following ratios are recommended for the preparation of the reaction solution (preparation on ice).

*Do not add more than 1/10 of the RT-qPCR volume of the reverse transcription product. high concentration of template will easily lead to non-specific amplification, appropriate dilution of 5-50 times. The recommended amount of template is 4 ?L, try not to exceed 6 ?L. When the reaction performance is poor, the primer concentration can be adjusted in the range of 0.2-1.0 ?mol/L.

2?Fluorescence quantitative PCR amplification procedure (two-step method)

3?Rapid amplification procedure for fluorescent quantitative PCR (two-step method)

* The annealing/extension temperature and final extension time can be adjusted appropriately according to the experimental requirements. The rapid program is suitable for most of the genes, and the standard program can be tried for individual complex secondary structure genes.

 Notes

1. This product is for research use only.
2. Please operate with lab coats and disposable gloves?for your safety.

Ver.EN20230908

Documents:

Manuals

11172-Hieff™ Fast Cell Direct. EN20230908.pdf